Put the Center Column Base Stopper on the Upper part of Center Column. Remove the Center Column Base Stopper and then, remove the Lower part of Center Column. Extending the Tripod Legsįlip up the Leg Lock Lever to extend or shorten any of the individual leg sections to the desired length, and press the Leg Lock Lever flush against the Leg to lock. There is a choice of two other angle positions.Īfter choosing the desired leg angle, securely push in the Adjustment Lock. To change the angle of each leg, close the Leg slightly, and then pull the Leg Angle Adjustment Lock out. Tripod Section Three Position Adjustable Legs When attaching the Pan Head to a tripod with a small thread(U1/4) use the optional small thread adapter. ![]() Do not attach camera directly to the threaded post of the Center Column. Tighten the Panning Lock Knob and turn clockwise slightly more. Set the new head, or accessory on the tripod's threaded post, and turn clockwise until it comes to a stop. The Pan & Tilt Handle and the Vertical Tilt Handle are grasped and then, turn the head counterclockwise forcibly. Next, tighten the Panning Lock Knob of the head firmly. Fix the Center Column of the legs firmly by both the Center Column Locking Collar and the Center Column Stopper. Please exchange by the following method to attach other heads or accessories to this leg. Removing the Pan Head from the Center Column When loosening either the Pan & Tilt Handle, or the Vertical Tilt Handle, take precaution by keeping a firm grip on the handle until the Pan Head is locked down. Always hold on to the camera during such operation. The camera may fall suddenly when the Locking Lever is loosened, causing damages and injuries. Safeguards during operation with a Camera Two bubble levels are built-in for vertical and horizontal positioning. Loosen the Vertical Tilt Handle, and the level can be adjusted. Loosen the Panning Lock Knob, and the head will rotate along the horizontal direction. Loosen the Pan & Tilt Handle, and the head will tilt back and forth. Care of the TripodĭO NOT apply any grease or oil to this product.Ĭlean with a mild detergent and a soft cloth only.ĭO NOT use close to flame. 8mm above the Plate and then, tighten the small screw by an Allen wrench.īe sure to open all three legs completely in order to prevent camera shaker, or accidental tip overs caused by unstableness. Then, screw it in again after reversing top and bottom. Loosen the Pan Head fixing screw and pull it out.Loosen the Plate without removing the small screw.Loosen the small screw in about three turnings with an Allen wrench (2mm width).The Pan Head fixing screw is reversible for either large thread (U3/8) or small thread (U1/4). Column from falling out.īy inverting the Center Column, it is possible to do copy, and close up work. ![]() Make sure to re-attach the Center Column By inverting the Center Column, it is possible to Base Stopper, in order to prevent the Center do copy, and close up work. Insert the Center Column from the lower side of Main Body, and tighten the Locking Collar and the Center Column Stopper. Loosen the Center Column Stopper and the Locking Collar, and then pull out the Center Column. ![]() Remove the Center Column Base Stopper truning to the way of arrow. Inverting the Center ColumnĪlways remove the Pan Head when replacing the Center Column. We therefore, recommend that you remove your camera when carrying the tripod. Carrying the TripodĬarrying a tripod with a camera left on can result in unexpected accidents. A loose mounting screw may go unnoticed, and result in a sudden accidental fall. Please do not use equipment exceeding this limit.Įquipment with uneven weight distribution should not be panned by the Quick Shoe. This product is designed to withstand equipment up to 5kgs. Pan HeadĮquipment that can be used with this Tripod The bolts of the Pan Head marked " " should not be adjusted nor operated. Soft Grip is consumption and cannot be used parmanently. Please refer to instructions closely to avoid accidents. This prohibited icon refers to information pertaining to prohibited contents. This caution icon refers to information pertaining to important safety procedures in preventing injuries, or damages which may occur as a result of mishandling this product. Retain this instruction sheet in case you might want to refer back to it. Please take a few moments to read this instruction sheet carefully before use so that you can take full advantage of your Tripod's many fine features. The SLIK Corporation has designed your tripod to be a sturdy, rugged, dependable product that will provide you with many years of satisfactory use.
0 Comments
Leave a Reply. |